diff --git a/include/configs/mx6sabreauto.h b/include/configs/mx6sabreauto.h
new file mode 100644
index 0000000..fd0d5ce
--- /dev/null
+++ b/include/configs/mx6sabreauto.h
@@ -0,0 +1,79 @@
+/*
+ * Copyright (C) 2012 Freescale Semiconductor, Inc.
+ *
+ * Configuration settings for the Freescale i.MX6Q SabreAuto board.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __MX6SABREAUTO_CONFIG_H
+#define __MX6SABREAUTO_CONFIG_H
+
+#ifdef CONFIG_SPL
+#include "imx6_spl.h"
+#endif
+
+#define CONFIG_MACH_TYPE	3529
+#define CONFIG_MXC_UART_BASE	UART4_BASE
+#define CONSOLE_DEV		"ttymxc3"
+#define CONFIG_MMCROOT			"/dev/mmcblk0p2"
+
+/* USB Configs */
+#define CONFIG_USB_HOST_ETHER
+#define CONFIG_USB_ETHER_ASIX
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET	/* For OTG port */
+#define CONFIG_MXC_USB_PORTSC	(PORT_PTS_UTMI | PORT_PTS_PTW)
+#define CONFIG_MXC_USB_FLAGS	0
+
+#define CONFIG_PCA953X
+#define CONFIG_SYS_I2C_PCA953X_WIDTH	{ {0x30, 8}, {0x32, 8}, {0x34, 8} }
+
+#include "mx6sabre_common.h"
+
+#define CONFIG_SYS_FLASH_BASE           WEIM_ARB_BASE_ADDR
+#define CONFIG_SYS_FLASH_SECT_SIZE      (128 * 1024)
+#define CONFIG_SYS_MAX_FLASH_BANKS 1    /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 256   /* max number of sectors on one chip */
+#define CONFIG_SYS_FLASH_CFI            /* Flash memory is CFI compliant */
+#define CONFIG_FLASH_CFI_DRIVER         /* Use drivers/cfi_flash.c */
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* Use buffered writes*/
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
+
+#define CONFIG_SYS_FSL_USDHC_NUM	2
+#if defined(CONFIG_ENV_IS_IN_MMC)
+#define CONFIG_SYS_MMC_ENV_DEV		0
+#endif
+
+/* I2C Configs */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_MXC
+#define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
+#define CONFIG_SYS_I2C_MXC_I2C2		/* enable I2C bus 2 */
+#define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */
+#define CONFIG_SYS_I2C_SPEED		100000
+
+/* NAND flash command */
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_NAND_TRIMFFS
+
+/* NAND stuff */
+#define CONFIG_NAND_MXS
+#define CONFIG_SYS_MAX_NAND_DEVICE     1
+#define CONFIG_SYS_NAND_BASE           0x40000000
+#define CONFIG_SYS_NAND_5_ADDR_CYCLE
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+
+/* DMA stuff, needed for GPMI/MXS NAND support */
+#define CONFIG_APBH_DMA
+#define CONFIG_APBH_DMA_BURST
+#define CONFIG_APBH_DMA_BURST8
+
+/* PMIC */
+#define CONFIG_POWER
+#define CONFIG_POWER_I2C
+#define CONFIG_POWER_PFUZE100
+#define CONFIG_POWER_PFUZE100_I2C_ADDR	0x08
+
+#endif                         /* __MX6SABREAUTO_CONFIG_H */